 |
| Tech Support |
|
| Writing Specifications (section 06 61 16) |
|
|
" Staron® Solid Surfaces make an elegant, hygienic
and easy-to-maintain surface in any kitchen " |
|
|
|
|
|
GENERAL NOTES TO SPECIFIER:
This specification section has been prepared to assist design professionals in the preparation
of project or office master specifications. It follows guidelines established by the Construction
Specifications Institute, and therefore may be used with most master specification systems with
minor editing.
Edit carefully to suit project requirements. Modify as necessary and delete items that are not
applicable. Verify that referenced section numbers and titles are correct. (Numbers and titles
referenced are based on Masterformat, 2004 edition).
This section assumes the project manual will contain complete Division 1 documents including
01 25 13 - Product substitution procedures, sections 01 33 00 - Submittal procedures, 01
62 00 - Product options, 01 66 00 - Product storage and handling requirements, 01 74 00
- Cleaning and waste management, 01 77 00 - Closeout procedures, and 01 78 00 - Closeout
submittals. Close coordination with Division 1 sections is required. If the project manual does
not contain these sections, additional information should be included under the appropriate
articles.
This is a proprietary specification.
Notes to the specifier are in blue and should be deleted from final copy.
Optional items requiring selection by the specifier are enclosed within brackets, e.g. [35] [40]
[45]. Make appropriate selections and delete others.
Items requiring additional information are underlined blank spaces, e.g. _______________.
Optional paragraphs requiring selection of one of the options are separated by a bold, reddish "or," e.g. - OR.
Optional paragraphs and features that may be selected or deleted as desired are shown in bold
type. Delete bold type when including these paragraphs or features.
Revise footer to suit project/office requirements.
Part 1. GENERAL
1.01 SUMMARY
A. Section includes:
List types of various applications included in the project below. e.g., paneling and trim, tub/shower surrounds
(vertical); tub decks, work surfaces (horizontal); window sills (miscellaneous fabrications).
1. Vertical applications
a. __________________.
b. __________________.
2. Horizontal applications
a. __________________.
b. __________________.
3. Miscellaneous fabrications.
a. __________________.
b. __________________.
B. Related Sections:
Include appropriate sections below for other sections specifically related to installation of products specified herein.
1. Section _______ - ______________.
2. Section _______ - ______________.
3. Section _______ - ______________.
Include appropriate language below if products specified in this section are to be bid as alternates.
Otherwise delete the following paragraph.
C. Alternates:
1. Reference Section 01 23 00 - Alternates.
1.02 SUBMITTALS
A. Reference Section 01 33 00 Submittal Procedures; submit following items:
Delete requirements for color submittals in subparagraphs 1 and 4 below if colors are specified in article 2.02
or are shown on drawings.
- Product Data.
a. Solid surface sheet material.
b. Include standard color chart showing full range of available colors for sheet
material.
- Material Safety Data Sheets (MSDS) for products and accessories.
- Shop Drawings: Provide plans, elevations, sections, and large scale details.
Include attachment provisions and fabrication methods.
- Samples for Final Color Verification: 4" x 4" (100 x 100 mm) samples of color(s) selected from
initial color chart submittals.
- Quality Assurance/Control Submittals:
a. Qualifications: Proof of fabricator qualifications.
b. Certificates: Copies of ISO certifications.
c. Test Reports:
1). Flammability test reports.
2). Food preparation zone use test reports.
d. Manufacturer¡¯s Fabrication and Installation Manual.
e. Manufacturer¡¯s Fabrication and Installation Check List.
B. Closeout Submittals: Reference Section 01 78 00 Closeout Submittals; submit following items:
- Care and Maintenance Instructions.
- Secial Warranties.
1.03 QUALITY ASSURANCE
A. Qualifications: Fabricator/Installer Qualifications: Minimum three years experience in fabrication
and
installation of solid surface materials or certification by Distributor.
B. Certifications: Manufacturer must hold current ISO 9002 and 14001 certificates.
1.04 DELIVERY, STORAGE AND HANDLING
A. Reference Section 01 66 00 Product Storage and Handling Requirements.
B. Follow manufacturer's instructions.
C. Special Instructions: Do not deliver components to project site until spaces are ready for
installation.
1.05 PROJECT/SITE CONDITIONS
Environmental Requirements: Installation spaces must be maintained at normal occupancy temperature
and humidity levels for minimum 72 hours prior to and continuously following installation.
1.06 WARRANTY
Special Warranty: Ten year limited warranty against manufacturing defects in sheet material.
1.07 MAINTENANCE
Extra Materials: Provide for future repair use by Owner.
- Minimum [4 sf (0.37 m2) per 100 sf (9 m2)] [ ___________ ] of each sheet material color.
- Minimum [3 lf (1.0 m) per 100 lf (30 m)] [ ____________ ] of each trim material color.
- Colors shall be from same dye-lot as installed products.
Part 2. PRODUCTS
2.01 MANUFACTURER
A. Samsung Chemical USA, Inc. Tel: (562) 926-5520
14251 E. Firestone Blvd, Suite 101 Fax: (562) 926-9930
La Mirada, CA 90638 Website: http://www.staron.com
Insert name, address and phone numbers of local distributor below.
1. Distributor:
B. Substitutions: None permitted.
2.02 MATERIALS
Select colors for following paragraphs A.1. and B.2. from manufacturer's current catalogs to specify below or show on drawings. Include subparagraphs a. only if architect will select colors following award of contract, and if more than one color will be selected.
A. Staron® Solid Surfaces Sheet: Homogenous sheet composed of a blend of natural minerals
and 100 percent acrylic resin (methyl methacrylate) complying with ANSI Z124.3 and Z124.6,
Type 6.
1. Physical Performance Characteristics:
a. Flammability Test (flame spread and smoke developed):
1). Test Procedure: NFPA 255.
2). Rating: Class A.
b. Food Zone Use:
1). Test Procedure: NSF 51.
2). Rating: Pass.
B. Use
1. Vertical Surfaces: 1/4" (6 mm) thick, unless otherwise shown on Drawings.
a. Color: [ _____________ ] [As shown on Drawings] [As selected by Architect].
1). Architect will select one color only.
OR
2). Architect may select up to [ ] separate colors.
b. Finish: [Matte] [Semi-gloss] [Polished] [As shown on Drawings].
2. Horizontal Surfaces: 1/2 in (12.3mm) thick, unless otherwise shown on Drawings.
a. Color: [ ] [As shown on Drawings] [As selected by Architect].
1). Architect will select one color only.
OR
2). Architect may select up to [ ] separate colors.
b. Finish: [Matte] [Semi-gloss] [Polished] [As shown on Drawings].
3. Miscellaneous Fabrications: Thickness and configuration as shown on Drawings.
a. Color: [ ] [As shown on Drawings] [As selected by Architect].
1). Architect will select one color only.
OR
2). Architect may select up to [ ] separate colors.
b. Finish: [Matte] [Semi-gloss] [Polished] [As shown on Drawings].
2.03 ACCESSORIES
A. Joint and Laminating Adhesive for bonding Staron® Solid Surfaces sheet to Staron® Solid
Surfaces sheet: Two component Staron® Solid Surfaces Joint Adhesive.
B. Adhesive for Bonding Staron® Solid Surfaces sheet to other materials: 100 percent silicone
sealant complying with ASTM C 920 or neoprene-based panel adhesive.
2.04 FABRICATION
A. Follow instructions in manufacturer's Fabrication and Installation Manual.
B. Fabricate solid surfacing in accordance with shop drawings.
C. Shop Assembly: Fabricate components in shop to the greatest extent practical.
D. Provide holes and cutouts for penetrations as shown on Drawings.
Part 3. EXECUTION
3.01 EXAMINATION
A. Examine substrates upon which solid surfacing will be installed.
Review manufacturer's
Fabrication and Installation Check List.
B. Coordinate with responsible entity to correct unsatisfactory conditions.
C. Commencement of work by installer is acceptance of substrate conditions.
3.02 INSTALLATION
Manufacturer's installation instructions are adequate for normal installation conditions.
Unusual conditions may require additional information in this article.
A. Install solid surfacing and secure to substrate in accordance with manufacturer's Fabrication
and
Installation Manual.
1. Provide 1/8" (3 mm) expansion joint for every 10' (3 m) of wall cladding when cladding is
enclosed by perpendicular walls at both ends or restrained on both ends by other
objects.
3.03 REPAIR
A. Repair minor imperfections and cracked seams and replace sections of severely damaged surfaces
in accordance with manufacturer¡¯s Fabrication and Installation Manual.
3.04 CLEANING
A. Reference Section 01 74 00 ? Cleaning and Waste Management.
B. Clean surfaces in accordance with manufacturer¡¯s Care and Maintenance Instructions.
3.05 PROTECTION
A. Cover horizontal surfaces with heavy paper or cardboard to protect from damage until
[date of Substantial Completion] [acceptance by Owner].
END OF SECTION1
Click to download DOC
Click to download PDF
|
|
|
|
