 |
| Tech Support |
|
| MSDS - Staron® Solid Surfaces Sheets |
|
|
" Staron® Solid Surfaces make an elegant, hygienic
and easy-to-maintain surface in any kitchen " |
|
|
|
|
|
1. Product and Company Identification
PRODUCT NAME: Staron® Solid Surfaces solid surface sheet
COMPANY: Cheil Industries Inc.
EMERGENCY TELEPHONE: 82-61-689-1531
ADDRESS: Yeosu Plant, Chemicals Division, Cheil Industries Inc.
62, Pyong Yo-Dong, Yeusu-Shi, Cheon Nam, Korea
2. Composition/Information on Ingredients
INGREDIENT: Acrylic Polymer
INGREDIENT SEQUENCE NUMBER: 01
PERCENT: 40~45
CAS NUMBER: 9011 - 14 - 7
INGREDIENT: Hydrated Alumina, Aluminum Hydroxide, Aluminum Trihydroxide
INGREDIENT SEQUENCE NUMBER: 02
PERCENT: 55~60
NIOSH(RTECS) NUMBER: BD094000M
CAS NUMBER: 21645 - 51 - 2
3. Hazards Identification
"Staron® Solid Surfaces sheet" is not hazardous when shipped. However, operations such as sawing, routing, drilling
and sanding can generate dust. High concentrations of dust can irritate eyes, nose and respiratory
passages and cause coughing and sneezing. Even though there is no exposure limit established for
dust from "Staron® Solid Surfaces sheet" (see details in the Exposure Controls/Personal Protection section of this
MSDS), avoid breathing dust.
"Staron® Solid Surfaces sheet" does not offgas at room temperature. At higher temperatures, a small amount of
methyl methacrylate may be released. The amount depends on temperature, time and other variables. Methyl methacrylate vapors can irritate eyes, skin, nose, and throat and cause allergic skin rashes. Over exposure to methyl methacrylate vapors can cause headache, nausea, weakness and lung irritation with coughing, discomfort and shortness of breath. Individuals with pre-existing lung or
skin problems may be more susceptible to the effects of over exposure to methyl methacrylate.
4. First Aid Measures
INHALATION: Move to fresh air
EYE CONTACT: Not applicable
SKIN CONTACT: Not applicable
INGESTION: Not applicable
5. Fire Fighting Measures
AFTER SPILLAGE/LEAKAGE/GAS LEAKAGE: Keep away from all ignition sources. Ensure adequate ventilation. Use personal protective equipment. Soak up with inert absorbent material. Clean with detergents. Avoid solvents.
EXTINGUISHING MEDIA: Dry powder, foam, carbon dioxide, water spray.
6. Accidental Release Measures
Review FIRE FIGHTING MEASURES and HANDLING AND STORAGE sections before proceeding
with clean-up. Use appropriate personal protective equipment during clean-up.
7. Handling and Storage
HANDLING: Sheets should be unloaded with a forklift or other lifting device capable of handling
pallets safely. If a lifting device is not available, always carry single sheets in the vertical position,
and wear heavy-duty protective gloves and proper safety shoes. Carrying should be done by two
people facing each other on short sides with one hand under to support and the other hand on
top to control the sheet.
STORAGE: Keep sheets flat and evenly supported at temperatures between 15 ~ 23¢ªC (59¢ª ~ 73¢ªF),
in a dry and well-ventilated indoor area.
8. Exposure Controls/Personal Protection
TECHNICAL PROTECTIVE MEASURES: Provide for appropriate exhaust ventilation and dust collection at machinery.
PERSONAL PROTECTIVE EQUIPMENT:
RESPIRATION (DURING MACHIINING OPERATION): In case of insufficient ventilation, wear
appropriate respiratory equipment in compliance with local regulations.
EYES (DURING MACHINING OPERATION): Use tightly fitting safety goggles or face-shield.
HANDS (DURING MACHINING OPERATION): Wear protective gloves.
OTHERS (DURING MACHINING OPERATION): Use ear protection, safety shoes.
Those who are highly sensitive should take precautions due to possible eye, nose or throat irritation
from Staron® Solid Surfaces dust and fumes.
9. Physical and Chemical Properties
FORM: Solid sheet
COLOR: Various
OROR: None
BOILING POINT: Not applicable
MELTING POINT: Not applicable
SPECIFIC GRAVITY (WATER = 1): 1.6 ~ 1.8
VAPOR PRESSURE (MMHg): Not applicable
VAPOR DENSITY (AIR = 1): Not applicable
SOLUBILITY IN WATER: Insoluble
pH: Not applicable
FLASH POINT: Not applicable
IGNITION TEMPERATURE: Not applicable
EXPLOSION LIMITS: Lower = Not applicable
Upper = Not applicable
10. Stability and Reactivity
THERMAL DECOMPOSITION PRODUCT: Frictional heat generated from sawing and routing Staron® Solid Surfaces sheet can reach or exceed a temperature of 300¢ª C. This is high enough to release a small amount of methyl methacrylate vapor.
HAZARDOUS DECOMPOSITION PRODUCT: Carbon monoxide, methyl methacrylate monomer, smoke
HAZARDOUS REACTION: None
FURTHER INFORMATION: Sprayed mist may be flammable at temperatures below the flash point
11. Toxicological Information
METHYL METHACRYLATE
TLV-TWA = 100 ppm = 410 mg/m3 ; ACGIH (1991-2)
LD50/oral/rat = 7872 mg/kg ; RTECS, 47796
Methyl methacrylate can be present on the cutting tool face at a concentration exceeding
the TLV of 100 ppm. However, it dissipates to very low levels with good ventilation.
12. Ecological Information
No information available
13. Disposal Considerations
Can be landfilled or incinerated, when in compliance with local regulations.
14. Transport Information
Not classified as dangerous in the meaning of transport regulations.
15. Regulatory Information
U.S. FEDERAL REGULATIONS
TSCA Inventory Status: In compliance with TSCA Inventory requirements for commercial purposes.
16. Other Information
ADDITIONAL INFORMATION
Do not use in medical applications involving permanent implantation in the human body.
We hereby certify that the above statements are true and correct in every respect.
If the statements are not true, all responsibility will belong to CHEIL.
Signature/Issued Date :
Staron® Solid Surfaces
CHEIL INDUSTRIES INC.
Click to download PDF
|
|
|
|
